crta
Hrvatska znanstvena Sekcija img
bibliografija
3 gif
 Naslovna
 O projektu
 FAQ
 Kontakt
4 gif
Pregledavanje radova
Jednostavno pretraživanje
Napredno pretraživanje
Skupni podaci
Upis novih radova
Upute
Ispravci prijavljenih radova
Ostale bibliografije
Slični projekti
 Bibliografske baze podataka

Pregled bibliografske jedinice broj: 779115

Časopis

Autori: Gavić, Lidia; Goršeta, Kristina; Glavina, Domagoj; Czarnecka, Beata; Nicholson, John W.
Naslov: Heat transfer properties and thermal cure of glass-ionomer dental cements
Izvornik: Journal of Materials Science: Materials in Medicine (0957-4530) 26 (2015), 10; 249-255
Vrsta rada: članak
Ključne riječi: Glass ionomer; Heat transfer; Thermo-curing
Sažetak:
Abstract Under clinical conditions, conventional glass- ionomer dental cements can be cured by application of heat from dental cure lamps, which causes acceleration in the setting. In order for this to be successful, such heat must be able to spread sufficiently through the cement to enhance cure, but not transmit heat so effectively that the underlying dental pulp of the tooth is damaged. The current study was aimed at measuring heat transfer properties of modern restorative glass-ionomers to determine the extent to which they meet these twin requirements. Three commercial glass ionomer cements (Ionofil Molar, Ketac Molar and Equia™ Fill) were used in association with three different light emitting diode cure lamps designed for clinical use. In addition, for each cement, one set of specimens was allowed to cure without application of a lamp. Temperature changes were measured at three different depths (2, 3 and 4 mm) after cure times of 20, 40 and 60 s. The difference among the tested groups was evaluated by ANOVA (P < 0.05) and post hoc Newman–Keuls test. All brands of glass-ionomer showed a small inherent setting exotherm in the absence of heat irradiation, but much greater temperature increases when exposed to the cure lamp. However, temperature rises did not exceed 12.9 °C. Application of the cure lamp led to the establishment of a temperature gradient throughout each specimen. Differences were typically significant (P < 0.05) and did not reflect the nominal power of the lamps, because those lamps have variable cooling systems, and are designed to optimize light output, not heating effect. Because the thermal conductivity of glass-ionomers is low, temperature rises at 4 mm depths were much lower than at 2 mm. At no time did the temperature rise sufficiently to cause concern about potential damage to the pulp.
Izvorni jezik: ENG
Current Contents: DA
Citation Index: DA
Ostale indexne publikacije: INSPEC;Science Citation Index Expanded (SciSearch);Journal Citation Reports/Science Edition;PubMed/Medline;SCOPUS;EMBASE;Chemical Abstracts Service (CAS);Google Scholar;EBSCO;CSA;Academic OneFile;Chimica;CSA Environmental Sciences;Current Contents/ Life Sciences;Earthquake Engineering Abstracts;EI-Compendex;INIS Atomindex;OCLC;OmniFile;PASCAL;Polymer Library;Referativny
Kategorija: Znanstveni
Znanstvena područja:
Stomatologija
Puni text rada: 779115.Heat_transfer_2015_26_249.pdf (tekst priložen 1. Lis. 2015. u 09:37 sati)
Tiskani medij: da
URL Internet adrese: http://link.springer.com/article/10.1007%2Fs10856-015-5578-0
Broj citata:
Altmetric:
DOI: 10.1007/s10856-015-5578-0
Google Scholar: Heat transfer properties and thermal cure of glass-ionomer dental cements
Upisao u CROSBI: Kristina Goršeta (kgorseta@sfzg.hr), 1. Lis. 2015. u 09:37 sati



  Verzija za printanje   za tiskati


upomoc
foot_4